Quantcast
Channel: EngineerZone: Message List
Browsing all 36216 articles
Browse latest View live

Re: Trouble running the ADAU1701 at 192kHz

Well, I couldn't wait until tomorrow so I went out in the lab and gave your instructions a try.  Sure enough, it works a treat.  Everything is running at 192kHz and happy as a clam.  I did have to...

View Article


Re: AD9361 - Connecting external LO and using internal LO

Thank you

View Article


Image may be NSFW.
Clik here to view.

ADT7310,ADT7312可以用于真空环境的温度测量吗?

我用过ADT7310,但是不知道ADT7310是否能用于ADT7310。如果不能,请推荐一款温度传感器用于真空环境的温度测量!

View Article

Re: MAT14 Cebo spefification

Hi VickyW-san, Thank you for your verification. Best Regards,Ricky

View Article

Re: Problem reading output from AD7961 FMC Board in Zedboard.

Hi, Shan. Yes. You may set EN = 0001. Or you may still have it at 0010 but change LK7 to use the 4.096V REF from the ADR4540. The 2_048V REFIN is actually a test point for the ADR4520 output, thus the...

View Article


Load Cell Amplifier Needed

Hello. I am using a ELHS-T1E-AC load cell that gives a 200mV output. Can anyone recommend an amplifier that can amplify the 200mV output to around +/- 10V with low noise?

View Article

Re: ADV7612 and ADV7513

Thanks GuenterL.... We will select 16-bit ITU-656 SDR mode (OP_FORMAT_SEL = 0x80) with discrete H & V syncs. Please tell us if any device driver support is available for ADV7612?

View Article

Re: Is my ADAS1000 broken?

Good day sir, I noticed the REFIN of one device is connected to REFOUT of same device isn't it? This should be 1.8V right? I'm reading 0.19V only I guess my chip was broken. However I want to ask other...

View Article


Re: ad7730 interfacing problem

Hi Pranav,      There is a thread that is quite similar to your problem. Kindly refer to this link https://ez.analog.com/message/172560#172560. Please also try to do a reset after power up. This will...

View Article


Re: ADV7393: what's the way to increase the amplitude of the video output?

thanks.found an error in my schematic, that solved the case. again thanks. Ofek.

View Article

Output impedance of HMC1041LC4

Hi, I would like to know output impedance of IF1 ( pin 11) and IF2 (pin 9) of HMC1041LC4. Is to 50 ohms or other value? Best Regards,

View Article

Re: Load Cell Amplifier Needed

Hi Chris,You can use ADA4004-1 (1.8 nV/√Hz, Precision Amplifier). It has a maximum of 125uV offset voltage, high gain (up to 120 dB), wide bandwidth (12 MHz), low drift (0.7 μV/°C) which makes it ideal...

View Article

Image may be NSFW.
Clik here to view.

Data Acquisition System

HelloI have to make 2 isolated channel simultaneous sampling data acquisition system. I don't know how to start the project. If anyone has any idea or advice it will be a great help.Thanks in advance.

View Article


Re: EV AD9910 Output Filter

Hey Meir, Did you used the same circuit as in the Evaluation board or you have done some modification.?Please share the details if yes. And what you are writing for ASF register.Please check and tell...

View Article

Re: Are there plans to support BF70X for linux distribution for blackfin

Hi Kenny, So far as I know there is no plan yet to support BF70x for Linux from ADI. We do have a customer, probabaly a solution provider has done some job on this, click U-boot for BF707-EZKIT.

View Article


Re: AD8310 Noise Floor

Hi Nikkee, Intercept does't have any relation ship. Intercept is the minimum detectable power by the log amplifier.Which means is the signal level is below the Intercept it will be considered as the...

View Article

Re: IIOD with Remote OSC

Great i checked it..no devices found on the target; am i missing something? maybe some <.config> includes at the kernel build or maybe it is some hw issue!? Someone could point me to a build...

View Article


Re: IIO Scope with KC705 + FMCOMMS2

(1) yep i have ping between the machines;(2) yep i run the iiod deamon on the target from command line to (maybe) see responses at the shell...still no success;iio_info reporting no devices on the...

View Article

Does ADV7186 support BT.1120 output?

Hi, I'd like to know whether ADV7186 can support BT.1120.ITU-BT.112074.25MHz60 frameYCbCr 16bit Embedded SyncBest regards, TomY

View Article

AD8347 Vcom Pin.

Hello, Please tell us the details about absolute maximum ratings of VCMO Pin of AD8347.I want to connect the VCMO pin and GND. Best regard

View Article
Browsing all 36216 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>