Clik here to view.
Re: Question for your IIO Oscilloscope
Ah,,,,I got it!I will let this know to customer.Thank you Lars!
View ArticleRe: separate ranking in expert leaderboard for non ADI employees
Hi,The leaderboard represents all users within the community employee and customer. When you log in you can see where you rank in the leaderboard under the "My Rank" tab.Regards,Lisa
View ArticleClik here to view.
Why does SSM3302 class-D power amp mute outputs?
We have designed in the SSM3302 Class-D audio amplifier into a product under development for use driving a piezoelectric transducer. The device is used in in mono mode with PVDD = 15VDC (19VDC also...
View ArticleRe: AD9361 AC701 no-os customized for CMOS mode
Sorry, your right, you are talking about a different clock. I thought you want to use the CMOS interface's clock signal. But you want to use the additional interface signal called CLOCK_OUT or CLKOUT...
View ArticleClik here to view.
Re: HMC849 RF switch PSRR
Hi Marc-Antoine, Figures below show the isolation between Vdd/Vctl/EN ports and RF ports of the HMC849ALP4CE. This measurement was done with standard eval board of the HMC849ALP4CE, there is a 100pF...
View ArticleRe: HMC783LP6CE serial port write operation
The FT2232D mode used on all ourevaluation software is ‘MPSSE’ mode, not ‘Fast Opto’ mode.
View ArticleRe: ADV7604 - Unstable hsync on output pixel port
I am checking with the ADV7604 expert again. I don't have a definitive answer why custom setting would be more stable then the presets.
View ArticleRe: libiio segmentation fault on write
Hi, I pushed a fix: FMCOMMS2 Sink/Source: Avoid segfaults when used with the FMCOMMS4 · 70b3e5c · analogdevicesinc/gnuradio · GitHub Regards, -Paul
View ArticleRe: ADV7181C Linux Driver
ADI linux drivers can be found hereLinux Drivers [Analog Devices Wiki]Unfortunately the ADV7181C does not exist here Some third part drivers are available herekernel/git/torvalds/linux.git - Linux...
View ArticleClik here to view.
Multiplexer output does not match the input
Hi there I have some strange effects on an analog multiplexer from Analog Devices where I need your help to understand why this can happen. I'm using the ADG758BCPZ 8:1 multiplexer with 5V power supply...
View ArticleClik here to view.
Re: AD9361 AC701 no-os customized for CMOS mode
Istvan, Is there a bit in the initialization structure in the no-os that allows me to enable this clock? Nick
View ArticleRe: AD9858 -Microcontroller No-OS Driver
Hi LouijieThanks for your Reply Actually we want to drive this DDS Chip by Xilinx FPGA .EDK or HDL
View ArticleRe: ADCMP582 Comparator: Disable Latch Feature.
Jay, Forgive me for being confused. Isn't 100mV below the minimum spec and thus an invalid condition? David
View ArticleRe: Second stage boot loader example for ADSP-21489
I refered to the EE-345 and thead in EZ:https://ez.analog.com/message/121089#121089but failed to run on ADSP-21489 EZKIT. 1) LED image programmed into on-board SPI flash, say offset 0x10000 use...
View ArticleRe: Second stage boot loader example for ADSP-21489
BTW, I was using EZ-BOARD 0.1, VisualDSP++5.1.1
View ArticleRe: Missing: SimRF Models of the AD9361 Agile RF Transceiver
Darren: Thanks for the question. The folks at ADI who helped MathWorks develop the model, and are most familiar with it, hang out on the software forums -- not on the transciever forums. That's why it...
View ArticleRe: AD9364 Tx monitor gain settings
Oleg: Sorry -- I will need to defer to Michael. It could be that no one has asked for that yet, so it's missing. It could be that the Rx gain setting controllers the Tx mon gain, when that input is...
View ArticleRe: Required Vivado, HDL and FPGA/Linux driver versions for FMCOMMS2/3 with...
You need to go to the web site to get "attachements" to messages. They don't come through on the email interface, to prevent as much spam as possible. - Robin
View ArticleRe: ZC702 / AD-FMCOMMS4 No OS System Modification Question
Darren: For those just getting familiar with things, we normally suggest using the Linux / Zynq design first. It's a little easier to use and interact with the AD9361 on either the fmcomms2 or 3. Once...
View ArticleRe: DAQ2 AD9680 Xilinx JESD204 Core
Peter: An eval version of the license is available. You don't need to purchase it to try things out. (Only to go to production). - Robin
View Article