Clik here to view.
ADV8005 4k2k(4096x2160)/30Hz output
Hi, Customer would like to have 4096x2160/30Hz output. I can't find any corresponding register settings. Can you please provide the settings for VSP(for any timing input) and Tx, thanks. The detail...
View ArticleClik here to view.
Re: Problems obtaining output on the BF527 LCD for LCDColorBar example
Hi David sir, I already mentioned above LCD problem,you remember that sir,We are Run the LCD program again and check it,the program were Run correctly so we use the stamp light and saw...
View ArticleRe: AD9889BBSTZ-165 resitor swing
Hi mattp,I've seen this thread before,We are having issue with settiong up right Voltage swing on TMDS lines going out from board,is there any graph for R_EXT versus current graph or table, We were...
View ArticleRe: AD9889BBSTZ-165 resitor swing
Hi mattp,I've seen this thread before,We are having issue with settiong up right Voltage swing on TMDS lines going out from board,is there any graph for R_EXT versus current graph or table, We were...
View ArticleClik here to view.
ADV7511 register configuration
Hi ADI experts,I have two questions on ADV7511 when I'm using it, please help to check and answer, thanks a lot.1. how to config the register under 1080p 30Hz format? I only find 1080p 60Hz format in...
View ArticleRe: FMCOMMS2 - external reference clock
Hi Ovidiu, You can't change the REF CLK frequency from the GUI.You have to edit the device tree: https://github.com/analogdevicesinc/linux/blob/xcomm_zynq/arch/arm/boot/dts/adi-fmcomms2.dtsi If you...
View ArticleWeighing Scale Design
Hi ChrisD.Rama I am trying to design a weighing scale with an internal system precision of 1:60000 counts. I am using ADuCM360 which has two inbuilt sigma-delta ADC's. I have a four wire load cell...
View ArticleADE 7758: Measurement of kW-hr
Hi,I am doing a project in which I want to measure active power of the 3 phases. For this I think the process is1) Specify through SPI which register you want to read2) Get the value of that register...
View ArticleClik here to view.
Re: Problems obtaining output on the BF527 LCD for LCDColorBar example
Hi David sir,1)Is any Simulator support for ADSP-BF527 with cross core Embedded studio version 1.0.2.0 or Visual DSP .then say how to access simulator tool..2)you mention SW23 in manual (i attach...
View ArticleClik here to view.
Re: WDTH_CAP problem with BF518
Hello,I am testing different configurations of timer6:*pTIMER6_CONFIG = (WDTH_CAP) | (TIN_SEL) | (PULSE_HI) | (IRQ_ENA) | (PERIOD_CNT);and I configured it to use interrupt priority...
View Articlead7401 discussion
Hi Dave, I have a questionfor you. Could you pleas help out . I was just going through the AD7401A data sheet. And trying to implement thesecond order delta modulator. From the Page 14 of the AD7401A...
View ArticleRe: Re: Re: Weighing Scale Design
Hi Ragavendra, Basing from your Block Diagram I just need to confirm if the 5V of the USB goes directly to the AVDD pin of the ADuCm360? Please note that the ADuCM360 has an absolute maximum...
View ArticleAD9361 Change BW
Dear sir: I want to change different Bandwidth (like LTE 5MHz to LTE 10MHz) in the running time, the procedure may beTx state ->reset->change BW ->Tx stateIf we follow the procedure as above,...
View ArticleRe: PVP in BlackFin BF609
Hi Bill,THC block cannot process selective pixels. It can however process pixels within a region or outside a region (ROI). I think what you are looking for is to process only 1 of several channels....
View ArticleAD9361 initialization and calibration
hey guys. I work on AD9361 with my XILINX-V6AD9361 initialization needs calibrations.my question is for some specific parts,like BBPLL VCO or RF synthesizer charge pump,shoule I first calibrate them or...
View ArticleRe: ADIS16209 Accuracy Problems and Assembly issues
Dear Mark,We have tested the values of the registers you had asked for:We got 0x3F51 in PROD_IDI and we got 0 and 0 in 0x1C and 0x1E. We are in a time pressing situation and we are no closer of...
View ArticleRe: trouble compiling with Blimp ADV7625 OSD IDE and Emulator
Hi Ron, We will look in to the problem by checking all the steps that you have given. Please let us know what is the Blimp version that you have been using. Best Regards,Jeyasudha.M
View Article[ADV7611] ABSOLUTE MAXIMUM RATINGS of "SCL/SDA Data Pins to DVDDIO" on...
Hello,I have a question about ABSOLUTE MAXIMUM RATINGS of ADV7611.There is a following description about ABSOLUTE MAXIMUM RATINGS of "SCL/SDA Data Pins to DVDDIO" on datasheet...
View ArticleRe: BF607 SMC Timing
Hi, Could you please confirm how you are measuring the AMS time? I believe you are doing so by probing the signals, and capturing on the oscilloscope. Could you please share the respective screenshot...
View Article